Wearable Breast Pump
Materno Flow 1264W


INFO CENTER

WHICH SECTION ARE YOU INTERESTED IN?

CONTROL PANEL

A1 Power / Mode Selection button: press and hold to turn on or off, short press to change operating mode.
A2 Suction level decrease button
A3 Suction level increase button
B1 Stimulation mode indicator
B2 Expression mode indicator
B3 Anti-stasis mode indicator
B4 Vibration mode indicator
B5 Level and time indicator

INSTRUCTIONS FOR USE


1. PREPARATION:
Before using the Materno Flow 1264W breast pump, wash your hands thoroughly. Make sure all components have been properly cleaned and assembled according to the assembly instructions.
Before starting expression, it is recommended to use a warm towel to apply compresses and gently massage the breast to help facilitate milk flow.

2. POSITIONING:
Place the assembled breast pump inside your bra, adjusting the angle so that it fits snugly and comfortably against the breast.

3. POWER ON:
Press and hold the "Power/Mode Selection (A1)" button to turn on the device, which will automatically enter stimulation mode. After 2 minutes of operation, the device will automatically switch to expression mode.

▶ HOW TO ADJUST THE SUCTION INTENSITY

  • During operation, briefly press the (-) and (+) buttons to adjust the intensity level of the current mode.

    • ▶ HOW TO CHANGE MODE

  • During operation, briefly press the A1 button to cycle through the available modes.

    • ▶ HOW TO ACTIVATE THE VIBRATION STIMULATION FUNCTION

  • During operation, press the (A2) and (A3) buttons simultaneously to add the “Vibration Mode” to the current operating mode. Press them again to deactivate it.

    • ▶ WHAT TO DO AT THE END OF THE EXPRESSION SESSION

  • When the session is finished, press and hold the button to turn off the device. Disconnect it and begin the cleaning procedures.
    After completing milk expression, remove the bottle and transfer the breast milk into a suitable container for storage.

    • ▶ MEMORY FUNCTION

  • Thanks to the memory function, the device remembers the last operating level used in stimulation, expression, anti-stasis, and vibration modes, making it easier to use during subsequent expression sessions.

    • 4 OPERATING MODES


    STIMULATION (LEVEL 1~5):
    In this mode, the breast pump generates a relatively fast suction rhythm with low suction power. It is designed to gently stimulate the breast tissue and promote milk flow by mimicking a newborn’s initial shallow sucking pattern. It is recommended to use this mode before switching to other modes.

    EXPRESSION (LEVEL 1~9):
    This mode mimics a newborn’s deeper and slower sucking rhythm during active breastfeeding. The suction strength is higher and the frequency is slower compared to stimulation mode. This setting is designed to help express milk more effectively once milk flow has started.

    ANTI-STASIS (LEVEL 1~9):
    The anti-stasis mode provides a pulsating suction rhythm to thoroughly remove residual milk from the breast after expression. Regular use may help prevent milk stasis, reduce the risk of blocked ducts, and maintain proper milk flow.

    VIBRATION STIMULATION MODE: (LEVEL 1~3)
    The breast pump delivers 13,000 gentle pulses per minute to deeply stimulate the breast, helping to release the milk ducts and facilitate milk expression.

    CLEANING AND MAINTENANCE


    WHAT TO DO AFTER EACH USE

    Disassemble and rinse all parts that come into direct contact with the breast and breast milk (excluding the main unit) in warm water to remove milk residues. Allow all parts to air dry completely and store the breast pump in a clean, dry place.

    HOW TO DISINFECT DAILY

    ▶️ Wash your hands thoroughly.
    ▶️ Separate all parts that come into direct contact with the breast and breast milk and need to be disinfected.
    ▶️ Use boiling water or a steam sterilizer for 5 minutes.
    ▶️ Place the sterilized parts on a clean towel and store them in a dry place when not in use.

    ⚠️ During sterilization, accessories must not come into direct contact with the metal walls of the container (it is recommended to use clean gauze as a separator between the parts and the container).

    CLEANING PRECAUTIONS

    ▶️ Disassemble all accessories that come into contact with the breast or breast milk (except the main unit).
    ▶️ After each use, clean the parts immediately to prevent residue buildup and bacterial growth.
    ▶️ Make sure to assemble/disassemble each accessory according to the specific instructions, ensuring that no parts are lost during assembly or disassembly.
    ▶️ All silicone components can be sterilized (except the main unit).
    ❌ Do not boil or steam sterilize the valve for more than 3 minutes.
    ❌ Do not boil or steam sterilize the milk collection container for more than 5 minutes.

    ▶ BEFORE FIRST USE

  • Before using the breast pump for the first time, thoroughly clean and disinfect all components (except the main unit and the USB cable), following the cleaning and disinfection instructions.

    • COMPONENTS

    1. Silicone cup
    2. Assembly body
    3. Anti-backflow valve
    4. Non-return valve
    5. Main unit
    6. Container
    7. Lid
    8. USB cable

    HOW TO CHARGE THE BATTERY

    This product uses a USB charging cable interface, allowing multiple power supply options:

    1. Connection to a computer USB port.
    2. Connection using the included adapter (5V2A).
    3. Connection to a power bank.

    The LED battery icon indicates the charging status:

    • If the battery symbol flashes during startup or use, it means the main unit needs to be recharged promptly.
    • Once the device is connected to a power source for charging, the battery symbol flashes to indicate that the battery is charging. When the battery is fully charged, the battery symbol remains steadily lit.
    Didn’t find what you were looking for? SEND YOUR REQUEST

    YOUR CART (0)

    No Products in the Cart