ASSEMBLY INSTRUCTIONS
WHICH SECTION ARE YOU INTERESTED IN?
HOW TO ASSEMBLE THE BREAST PUMP
▶️ Insert the breast shield "A" into the breast pump body "D".
▶️
Place the suction diaphragm "C" on top of the breast pump body.
Make sure that the edge of the silicone diaphragm fits perfectly and that the positioning notch is correctly aligned.
▶️
Attach the suction valve "E" to the bottom of the breast pump body and make sure it is fully inserted. The suction valve must not be installed horizontally.
▶️ Attach the assembled breast pump body to the milk collection container "H" and make sure the two parts fit together perfectly.
▶️ Insert the lid onto the container, sliding it along the guides until it is completely closed.
▶️ For pumping from one breast only, connect the main pump unit to the assembled milk collection container using a connecting tube.
INSTRUCTIONS FOR USE
▶️ Wash your hands before use and make sure the breast pump is thoroughly clean and correctly assembled according to the assembly instructions.
▶️
Adjust your nursing bra, secure the milk collection container, keep your body upright and start expressing once the pump has been correctly connected to the main unit.
▶️
If your nipple diameter does not match the diameter of the breast shield, you can use a silicone insert. Place the silicone insert inside the breast shield and make sure it fits snugly.
▶️ Once you have finished expressing, remove the breast pump, take the lid off the milk collection container to disassemble it, and pour the milk into a feeding bottle or breast milk storage bag.
HOW TO CHOOSE THE RIGHT SILICONE INSERT
Using a ruler or measuring tape, measure the diameter of your nipple (in mm) across its centre, excluding the areola.
Based on your measurement, choose the silicone insert that most closely matches the measured diameter:
- choose the 20 mm insert if your nipple measures up to 16 mm
- choose the 22 mm insert if your nipple measures up to 18 mm
- choose the 24 mm insert if your nipple measures up to 20 mm
Based on your measurement, choose the silicone insert that most closely matches the measured diameter:
- choose the 20 mm insert if your nipple measures up to 16 mm
- choose the 22 mm insert if your nipple measures up to 18 mm
- choose the 24 mm insert if your nipple measures up to 20 mm
3 OPERATING MODES
STIMULATION (LEVEL 1~9):
In this mode, the breast pump produces a relatively fast suction rhythm with low suction intensity. It is designed to gently stimulate breast tissue and encourage milk flow by mimicking a newborn baby's initial, shallow sucking pattern. It is recommended to use this mode before switching to the other modes.
EXPRESSION (LEVEL 1~9):
This mode mimics a baby's deeper, slower sucking rhythm during active breastfeeding. The suction intensity is higher and the frequency is lower than in stimulation mode. This setting is designed to help express milk more effectively once milk flow has started.
ANTI-STASIS (LEVEL 1~9):
The anti-stasis mode provides a pulsating suction rhythm to help remove residual milk from the breast after expressing. Regular use may help prevent milk stasis, reduce the risk of blocked milk ducts and maintain milk flow.
HOW TO ADJUST SUCTION INTENSITY
The pump will automatically switch off after 30 minutes of operation.
HOW TO CHANGE MODES
After 2 minutes of stimulation, the pump will automatically switch to expression mode.
The pump will automatically switch off after 30 minutes of operation.
HOW TO ACTIVATE ANTI-STASIS MODE
Press A4 again to increase suction intensity. The pump will automatically switch off after 5 minutes.
CLEANING AND MAINTENANCE
DO
✅ Clean washable accessories promptly after each use.
✅ Use soft sponge brushes and a mild detergent to clean this product.
✅ Accessories such as the connector body, breast shield, milk collection container, suction diaphragm and valve can be placed in a steriliser for disinfection.
✅ When disassembling and cleaning the breast pump, take care not to lose any small components. Losing a component may affect assembly and the correct operation of the breast pump.
✅ When cleaning, gently wash the valve, suction diaphragm and other parts to avoid damage that could affect normal operation.
DON'T
❌ Do not use steel wool, sharp tools or corrosive chemicals to clean this product.
❌ Do not heat-sterilise the silicone suction diaphragm or valve, as this may cause deformation and affect their functionality.
❌ Do not immerse the connecting tube or lid in water for cleaning. Clean them only with a clean, damp cloth.
(If they become wet, they may cause permanent damage to the breast pump's main unit).
❌ Do not sterilise this product in a microwave oven.
Didn't find what you were looking for? SUBMIT YOUR REQUEST