CONTROL PANEL
WHICH SECTION ARE YOU INTERESTED IN?
INSTRUCTIONS FOR USE
PREPARATION
▶️ Place the appliance on a clean, dry and flat surface.
▶️ Position the drain hose in the kitchen sink and plug in the power cord.
▶️ Open the lid of the water tank located below the control panel and add 3.5 l of fresh and clean water, if required by the wash programme.
▶️ Make sure the water level does not exceed the permitted limit, i.e. that it is between the MIN and MAX marks indicated in the tank.
⚠️ Do not add water to the
glass container.
HOW TO LOAD ITEMS
▶️ Remove any milk or food residues from the items to be washed.
▶️ Open the lid of the wash tub and place the bottles and other items to be washed facing downwards.
For more information, refer to the "instructions for loading items" section.
▶️ Make sure no item covers another and that water can reach all surfaces.
HOW TO START THE CYCLE
▶️ Add 2.5 ml of liquid dishwasher detergent, if required by the type of wash programme.
▶️ Close the lid of the wash tub, making sure the safety lock (red lever) is pressed.
▶️ Plug the cable into the wall socket.
▶️ Select the desired programme from the control panel and then press the "START" button to begin the cycle.
If during the wash cycle you need to stop and open the lid of the wash tub, press the "START/PAUSE" button to pause. Press the "START" button again to resume the wash cycle.
INSTRUCTIONS FOR LOADING ITEMS
▶️ Load items so that water can reach all surfaces for effective cleaning.
▶️ Do not stack items on top of each other: make sure no item covers another, to allow water to reach all surfaces.
HOW TO POSITION ITEMS
▶️ Position the dirty side of the bottle tilted downwards and the concave surface facing downwards to allow adequate cleaning and drainage of residual water.
▶️ The bottle teat can be hung diagonally on a central hook or on the raised holder on the lower level.
⚠️ Make sure no item obstructs the rotation of the spray arm and check that all items are securely positioned to prevent them from falling during washing or drying.
LOADING THE UPPER RACK
This rack is designed for lids,
rings, cutlery and small accessories.
The bottle neck holders allow them to be tilted, preventing residual water from pooling at the bottom.
The bottle neck holders allow them to be tilted, preventing residual water from pooling at the bottom.
LOADING THE LOWER RACK
The lower rack has 4 columns: 2 with a thin head and 2 with a thick head.
The thin heads can be used for internal cleaning of drinking bottle straws and small accessories, while the thick heads are ideal for bottles of different sizes.
Use the rubber spacers provided to keep items separated from each other.
The thin heads can be used for internal cleaning of drinking bottle straws and small accessories, while the thick heads are ideal for bottles of different sizes.
Use the rubber spacers provided to keep items separated from each other.
WASH PROGRAMMES
⚠️ Warning: keep the lid of the wash tub closed during the storage period for sterile items.
CLEANING AND MAINTENANCE
To prevent the build-up of limescale inside the water tank and in the washing mechanisms, it may be helpful to add 2 l of white alcohol vinegar mixed with 1.5 l of distilled water into the water tank.
Leave the solution to act for 15/20 minutes, then run the automatic wash cycle to remove deposits and clean the inside of the glass wash tub and plastic accessories.
At the end of the maintenance wash, remove both the water tank lid and the wash tub lid to allow the vinegar smell to dissipate into the air.
WHAT TO DO IF THE APPLIANCE IS NOT USED FOR LONG PERIODS
If the appliance is not used for long periods, to avoid stagnation, unpleasant odours and mould formation, we recommend running a cleaning cycle and opening the water tank lid and the wash tub lid to allow the interior to dry out completely.
Have you not found what you were looking for? SEND YOUR REQUEST