COMPONENTS
WHICH SECTION ARE YOU INTERESTED IN?
COMPONENTS
HOW TO USE
⚠️ BEFORE USE ⚠️
Make sure there are no insect stingers left in the stung area. If present, carefully remove the stinger before use.
▶️ Press the power button (2) to start the device. The device status LED
(1) lights up green 🟢, a buzzer sounds to indicate that the device
It's ready for use.
▶️ For a 3-second application , place the heating plate (4) of the device
on the tip or clamp area. Press the activation button once. The status LED of the
device (1) lights up blue 🔵 and signals that the application is starting.
▶️ For a 6 second application , place the heating plate (MCH) (4) of the device
on the tip or bite area. Press the activation button twice in quick succession. The
Device status LED (1) lights up yellow 🟡 and signals that the application is starting.
▶️ At the end of the application, a buzzer sounds, the heating of the
heating plate (MCH) (4) switches off automatically and the device status LED
(1) lights up green again 🟢 . Remove the heating plate (MCH) (4) from the area
skin once the signal is emitted.
▶️ To turn off the device, press the on/off button (2). The green LED 🟢
of the device status (1) turns off. If no other operation is performed within 5
minutes, the device will automatically turn off.
FOR SENSITIVE SKIN
The temperature of
treatment for sensitive skin is 47°C±2°C (116.6°F±3.6°F). This short application time (3 seconds)
It is also recommended for the first use of the device.
Depending on the sensitivity of your skin, the treatment temperature may be unpleasant and/or cause a slight skin redness.
If the heat is too high, stop treatment immediately.
Depending on the sensitivity of your skin, the treatment temperature may be unpleasant and/or cause a slight skin redness.
If the heat is too high, stop treatment immediately.
FOR NORMAL SKIN
The treatment temperature of the device is 50°C±2°C (122°F±3.6°F). This time
application (6 seconds) is recommended for regular use on normal skin.
CLEANING AND MAINTENANCE
✅ WHAT TO DO
▶️ Clean the device before first use and each additional use.
▶️ Turn off the device, let it cool down and remove the batteries before each cleaning.
▶️ Use only soft, dry cloths to clean the housing.
❌ WHAT NOT TO DO
▶️ Never use cleaning substances that could be potentially toxic if
come into contact with skin or mucous membranes, or if ingested or inhaled.
▶️ Do not use products
abrasives and never immerse the device in water.
▶️ Do not clean the device in the dishwasher.
▶️ Avoid mechanical cleaning with brushes or similar, as it may cause irreparable damage.
⚠️ ATTENTION ⚠️
When using the device on multiple punctures, it is recommended to clean the
heating plate every time. This reduces the possibility of transferring germs and bacteria from one area
skin to the other.
Use a commercially available alcohol-based disinfectant wipe to
disinfect the heating plate.
FREQUENTLY ASKED QUESTIONS
The device does not turn on
If your device does not turn on, there are two possible causes: the battery is not installed correctly or the batteries are dead.
If the battery installation was not successful, try reinstalling the battery and see if the problem is solved.
If the batteries are flat, proceed with replacing both batteries following the instructions for use.
If the battery installation was not successful, try reinstalling the battery and see if the problem is solved.
If the batteries are flat, proceed with replacing both batteries following the instructions for use.
The device no longer heats up enough
If your device no longer heats up enough, the battery level may be too low.
To resolve the issue, proceed by replacing both batteries following the instructions for use.
To resolve the issue, proceed by replacing both batteries following the instructions for use.
The device beeps 3 times / the device status LED flashes, even after turning the device off and on again
If your device beeps 3 times / the device status LED flashes (even after turning the device off and on again), the battery level of your device may be too low.
To resolve the issue, proceed by replacing both batteries following the instructions for use.
To resolve the issue, proceed by replacing both batteries following the instructions for use.
The application cannot be launched, even if the device status LED lights up green.
If you are unable to use your device even though the LED is lit green, we recommend that you restart your device.
To do this, press the power button again.
To do this, press the power button again.
The device beeps 5 times / the device status LED flashes, even after turning the device off and on again
If your device beeps 5 times or the device status LED flashes, even after you turn the device off and on again; your device may be defective.
To verify whether the product is defective and request a replacement, contact Customer Service.
Didn't find what you were looking for? SEND YOUR REQUEST