CONTROL PANEL
WHICH SECTION ARE YOU INTERESTED IN?
Frequently Asked Questions
▶️ Press and hold the power button to turn on the device; it will automatically enter heating mode with a preset temperature of 37°C.
▶️ To turn it off, press and hold the same button again.
⚠️ WARNING ⚠️
Use only the charger included in the package (5.0V 3.0A) for charging.
Using adapters other than the one provided may damage the device’s battery.
▶ BATTERY AND FIRST USE
▶ HOT'N'GO TURNS OFF AUTOMATICALLY IF:
Frequently Asked Questions
INSTRUCTIONS FOR USE
▶️ Unscrew the lid.
▶️ Add the liquid, then screw the lid back on tightly.
▶️ Screw the container onto the base to start using it.
▶️ Make sure the container and the base are properly aligned.
✅ HOW TO USE
▶️ Press the power button to quickly select the desired temperature between 37°C, 40°C, 45°C, 50°C, 55°C, 70°C, and 100°C.
▶️ Press the “–” or “+” buttons to adjust the temperature maintenance level between 37°C and 55°C.
▶️ Wait 3 seconds: the set temperature will flash three times to confirm the setting, then the real-time liquid temperature will be displayed.
▶️ During heating, once the set temperature (37°C - 55°C) is reached, the product will maintain the selected temperature until manually turned off.
⚠️ The temperature maintenance function does not activate for the 70°C and 100°C settings.
Frequently Asked Questions
✅ HOW TO USE
▶️ Pour the amount of water indicated in the table below into the product.
▶️ Insert the bottle.
▶️ Do not close the product’s lid.
▶️ Set the temperature to 70°C on the device: once the water inside reaches 70°C, the product will automatically turn off.
▶️ If the milk inside the bottle has not reached the desired temperature, repeat the above steps until the desired temperature is achieved.
❌ WHAT NOT TO DO
Do not use without water to avoid damage caused by overheating.
In the event of overheating, the product will automatically shut off.
⚠️ WARNING ⚠️
▶️ Always carefully check the milk temperature inside the bottle before feeding.
▶️ The product’s contents and the bottle will be very hot after heating.
▶️ The 100°C setting is not suitable for water bath heating, as it may cause excessive overheating of the bottle.
Frequently Asked Questions
▶️ Boil the water to 100°C using Hot'n'Go.
▶️ Let it cool down until it reaches a temperature of 70°C.
▶️ Add the milk powder directly into the container.
▶️ Close and shake the container to mix the milk.
▶️ Let the milk cool down to 37°C, the optimal temperature for feeding the baby.
Frequently Asked Questions
▶️ With the device turned on, press and hold the “–” and “+” buttons simultaneously to enter the 70°C heating mode.
▶️ Pour in the water and close the lid. The device will automatically turn off 3 minutes after reaching the set temperature. During heating, you can exit the mode by pressing the power button.
▶️ Add the milk powder directly into the container, close it, and shake to mix the milk.
▶️ Let the milk cool down to 37°C, the optimal temperature for feeding the baby.
Frequently Asked Questions
HOW TO REMOVE THE BASE BEFORE CLEANING
▶️ Hold the base of the container firmly.
▶️ Turn the base clockwise until the 🔒 symbol on the container aligns with the 🔽 symbol on the base, then remove the base.
▶️ Do not immerse the base directly in water to avoid damaging the internal components.
CLEANING STEPS
▶️ Turn off the device.
▶️ Unscrew the body of the container from the base for cleaning, but do not wash the base.
▶️ Regularly clean the conductive contacts on the base and under the container body to prevent dirt buildup.
▶️ After cleaning, make sure both the container and base are completely dry.
❌ WHAT NOT TO DO
DO NOT wash the kettle/milk warmer with the base attached to avoid damage to internal components.
HOW TO INSTALL THE BASE AFTER CLEANING
• Align the 🔒 lock icon on the base with the 🔽 icon on the container.
• Press down and turn the base counterclockwise until the 🔒 and 🔽 symbols are aligned.
Didn’t find what you were looking for? SEND YOUR REQUEST